Vertical Xcelerator IP Spezifikationen Seite 20
- Seite / 120
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
2-6 Using the Wizard Program
Chapter 2 - Installation
Xcelerator IP Administrator Manual March 2007
Using the Wizard Program
This Installation section will help you to install the Xcelerator IP quickly and easily. For
more detailed instructions and further setup options, refer to Chapter 5, Xcelerator IP
Configuration.
Setup Wizard
This system administrator can configure the Xcelerator IP remotely or locally via a Web
Browser. When Xcelerator IP is set to its default factory settings, the LAN address is
"192.168.1.1", the user name is "admin", and the password is "admin".
When the Xcelerator IP is started initially, or after being set to default configuration, the
Setup Wizard will activate upon system power up. The Setup Wizard is a series of menus
to assist the administrator with getting the Xcelerator IP up and running. The default
settings for the Setup Wizard will allow the Xcelerator IP to be operational out of the box.
For a detailed description of the Setup Wizard default settings, refer to “Xcelerator IP
Default Settings” on page 5-3.
The Setup Wizard allows the system administrator to select the appropriate programming
section(s) and configure the corresponding features. The following eight programming
sections are supported.
WAN Settings
LAN Settings
Wireless Basic
Wireless Security
Internet Time
Numbering Plan
IP Trunk
Call Routing Table
In the Setup Wizard, the administrator can navigate through the various programming
sections using the "Next" or "Back" buttons to choose the specific program to be
modified. At the end of the programming session, the administrator will select "Exit &
Reboot", at which time any changes to the system will be saved and the Xcelerator IP will
automatically reboot. The Setup Wizard runs only on initial startup of the Xcelerator IP.
Unless the Xcelerator IP is reset to its default configuration, the administrator will be
pointed to the Xcelerator IP home page when accessing the unit.
- Administrator Manual 1
- 1.0 3-07 Initial release 2
- Contents 3
- 4Phone Features 4
- 5 Xcelerator IP Configuration 5
- B Numbering Plan 5
- Introduction 7
- Product Description 9
- Office Location Diagrams 10
- Product Summary 11
- VoIP Protocols 12
- IP Trunk 12
- Digital Audio 13
- Security 13
- Configuration Management 13
- Radio - WLAN 13
- Remote Diagnostic 14
- Physical Interfaces 14
- Power Requirement 14
- Operating Environment 14
- Physical Specification 14
- Installation 15
- Hardware Components 17
- Gateway/Router 18
- Rear Panel 19
- Using the Wizard Program 20
- WAN Settings 21
- Chapter 2 - Installation 22
- LAN Setting 24
- Wireless Basic 25
- Wireless Security 26
- Internet Time 27
- Call Routing Table 30
- Wizard Setup Finished 30
- System Functions 31
- Access Control 33
- Answering Position 33
- Call Abandon 34
- Call Routing 34
- Caller ID 35
- Class Of Service (COS) 35
- Day & Night Service Mode 35
- Daylight Saving Time 35
- Default Set 35
- Chapter 3 - System Functions 36
- Gateway to Gateway 37
- Line Group Assignment 37
- Make an Outside Call 37
- Message Waiting Indication 37
- Trunk Group 40
- Wizard Setup 40
- Phone Features 41
- Comparing SIP Phone Features 43
- Alphanumeric Display 44
- Answer a Call 44
- Auto Answer 44
- Basic Call 44
- Direct Call Forward 45
- Busy Call Forward 45
- No Answer Call Forward 45
- Direct Call Forward to VM 45
- Call Log 46
- Call Waiting 46
- Caller Blocking 46
- Conference 47
- COS Following 47
- Distinctive Ringing 47
- Feature Key Programming 48
- Last Number Redial (LNR) 49
- LCD & Interactive Buttons 49
- On Hook Dialing 49
- Page Allow/Deny 49
- Phone Book 50
- Place a Call 50
- Register to a Server 50
- Speed Dial 51
- Transfer 51
- Voice Mail Access 52
- Volume Control 52
- Xcelerator IP Configuration 53
- System Setup 55
- Device Info (System Status) 56
- Advanced Settings 57
- LAN Parameters 58
- WAN Parameters 59
- Virtual Servers 62
- Port Trigger 62
- 5-12 Advanced Settings 64
- Incoming Filter 65
- Output Filter 65
- Parental Control 65
- 5-14 Advanced Settings 66
- Output Filter 66
- Traffic Class 68
- Bandwidth Control 68
- Dynamic DNS Menu 69
- Wireless Settings 70
- Wireless - Bridge Parameters 73
- Wireless - Station Info Menu 75
- Voice Settings 76
- Phone Menu 77
- Trunk Menu 78
- System Menu 85
- 5-36 Voice Settings 88
- Transmission 88
- Voice Mail Menu 92
- Management Settings 96
- Settings Menu 97
- Log Menu 98
- Registered Phone Menu 99
- Access Control Menu 101
- Update Menu 103
- Save & Reboot Menu 104
- Diagnostic Information 105
- System Prompts & 107
- Recordings 107
- Xcelerator IP Voice Prompts 109
- A-4 Preset Voice Prompts 110
- Preset Voice Prompts A-5 111
- A-6 Preset Voice Prompts 112
- Recording Voice Prompts 113
- Numbering Plan 115
- Xcelerator IP Default Values 117
Verwandte Produkte und Handbücher für Software Vertical Xcelerator IP
(4 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.522 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern